Every purchase made through our Amazon Affiliate Page helps support this site
-
Posts
287 -
Joined
-
Last visited
-
Days Won
18
Content Type
Profiles
Forums
Downloads
Gallery
Events
Store
Articles
Blogs
Posts posted by pkinneb
-
-
1 minute ago, Kev said:
Do you have a duplicating jig or just calipers and lots of patience? I think I see some subtle difference but, it's hard to tell.
I've been kind of looking at a duplicating jig for the lathe..
No I do not have a duplicator. I use the Peter Galbert Caliper (its a bit expensive)
but I only need one to do everything really simple to read etc. If you look close you will see my primary sizing by the small grooves on the piece (top center of the bulbs) these are the important things if you get these nailed the turning itself can be off a bit and the eye won't catch it. The line / grooves are very important as they are used for measuring when fitting the legs and arm posts if they are off it makes things a bit more challenging 🙂
- 1
-
Wow that looks great!!
- 1
-
18 hours ago, Kev said:
Moved your thread up here in the showcase..
Super nice work! Did you do all the spindle turnings as well? Almost seems a shame to put paint on it, the wood looks really good!
I did. Re the paint I think you'll be surprised with the finished product which will be black over red with rubbed in oil finish. It provides a really nice look since we are dealing with several wood species here; red oak steam bent bow & arm, red oak spindles, hard maple turnings, pine seat and white oak wedges.
Duplicating turnings from pattern:
15 hours ago, Chet said:That is a real piece of woodworking craftsmanship there. Is that done with green wood? Did you keep track of the hours?
Thanks Chet!! the Bow, Arm & Spindles are all green wood (almost dripping wet), seat is semi green 12% ish at the start and now at about 8%, turnings are kiln dried. RE hours about 60 so far, probably another 10 for the finish.
10 hours ago, Coop said:That’s cool! Really nice!
Thanks Coop! it definitely had some challenges with all the hole drilling at various angles and the spindle shaping. Getting those spindles through the arm while keeping a tight joint takes some practice 🙂
-
-
Great job Kev!!
- 1
-
I do this re if the tool is set up as it always cancels the error if there is one...
"Alternate faces.. If you look closely at my last picture, you'll see an F in one corner and an A in the other corner of each board. This is my note to do one edge "A"way from the fence and one side against the "F"ence.. If my fence is off, this will cancel out that small angle for a perfect glue joint."
That is one big piece to work single handed 🙂
Looks great!
- 1
-
That's an awesome piece Chet!!
- 1
-
That appears to be a pretty good deal for lightly used tools congrats!! Other than the price I cannot recall any negatives thoughts on my Festool items...well there was one sander I actually wasn't fond of and sold ...but considering how much I now own pretty much just price and you definitely hit a score there 🙂
-
On 2/2/2024 at 5:12 PM, Coop said:
They’re probably like me and break them down outside and no dc is needed.
yep!
-
I like @Chet use my TS55 to primarily knock down sheet goods and the only thing I would change is to go cordless if I were to do it over again.
-
Nice!!
-
17 hours ago, Coop said:
Wow, I’d give my left …… little finger for that much space!
That was my thought as well 🙂
-
Kev for what its worth I saw woodturningz.com had 4 pack of ornament blanks at a pretty good discount to Craft Supplies.
- 1
-
I have forced air furnace heat/ Air conditioning in my shop becuase mini splits weren't a thing when I built my shop but I have always thought if my unit craps out I would look at them for both space and cost considerations. Keep me posted we definitely get cold here -1 is the high for the next few days 🙂
-
Looks great!! I appreciate the mini split info as well I had heard they wouldn't work well in markets that cold good to know they have either improved or what I had read was not accurate.
-
On 1/8/2024 at 5:06 PM, Kev said:
Those are pretty cool!
Did you purchase the blanks or make them yourself? Where did you pick up the metal parts?
Picked up the blanks and the parts from Craft Supplies USA ...but I think I would look elsewhere for the blanks they were quite a bit bigger then required and I ended up cutting about 1/4" of two sides of each blank before turning.
- 1
-
-
Great looking lathe space Kev!!
- 1
-
Welcome!!
-
Happy New Year all!!
- 1
-
Happy holidays all wishing nothing but the best for you and your family's!!
- 2
-
Wow I saw that and thought it was cool...you actually acted on it and knocked one out I love it 🤣
- 1
-
Nice!!
- 1
-
Great job!! My ice cream scoops are probably single best liked xmas gifts I have made especially with the gents 🙂
Windsor Sack Back Chair
in Member Showcase
Posted
What I like is I have one tool for almost everything, I still use a 3/8" normal caliper for the arm post but don't have 5 or 6 going and no issues with them losing there setting etc. But $130 come on LOL